Installing A Bath tub
Installing A Bath tub
Blog Article
We have noticed this post about Tools You Need to Install a New Bathtub directly below on the net and thought it made perfect sense to share it with you on my blog.
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-hero-40160398595d4544b639b3398cdb247c.jpg)
Mounting a bathtub isn't exactly rocket science, yet it does need strong plumbing, woodworking, and also occasionally, tiling abilities. Replacing an old tub with a new one is additionally a reasonably hard task. If the old bathtub is readily easily accessible, the task can move quickly; if you have to open a wall surface to get rid of the old bathtub and position the new tub, the job is a lot harder. In either instance, the project is within a home handyman's skills, although you will need an assistant to vacate the old bathtub as well as embeded in the new one. Ensure you have actually certified yourself for the task and also fit attempting it. Instead of employing a contractor to take over a halfway-completed job, it is far better to take into consideration using one before you begin. Possibilities are you might require a specialist plumber to make tube links.
This article will assist you set up a brand-new bath tub in your bathroom if you have already gotten a brand-new tub as well as don't require to alter the setup of your previous supply of water pipelines.
Your devices and product list ought to make up the following:
Planning for the Installation
First of all, the sustaining structure provided with the bath ought to be fitted (if needed) according to the maker's guidelines. Next off, fit the taps or mixer to the bathtub. When fitting the tap block, it is very important to see to it that if the faucet features a plastic washing machine, it is fitted in between the bath and the taps. On a plastic bath, it is also practical to fit a supporting plate under the taps system to avoid stress on the tub.
Fit the adaptable faucet adapters to the bottom of both taps utilizing 2 nuts and also olives (sometimes supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet via the hole in the bathroom. Make use of the nut supplied by the producer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the flexible overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bathroom. See to it you make use of every one of the supplied washers.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Link the bottom of the overflow tube in a similar manner.The bath ought to now prepare to be suited its last placement.
Removing Old Touches
If you require to change old faucets with brand-new ones as a part of your setup, after that the first thing you must do is detach the water system. After doing so, activate the taps to drain any water staying in the system. The process of eliminating the existing faucets can be fairly bothersome as a result of the limited accessibility that is frequently the case.
Use a basin wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipes to the taps. Have a cloth ready for the remaining water that will come from the pipes. Once the supply pipelines have actually been gotten rid of, make use of the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the single taps from turning during this procedure. As soon as the faucets have actually been eliminated, the holes in the bath/basin will have to be cleaned of any old securing substance.
Prior to carrying on to fit the brand-new taps, compare the pipe links on the old faucets to the brand-new taps. If the old taps are longer than the brand-new faucets, after that a shank adapter is required for the new faucets to fit.
Installing the Bath tub
Making use of both wooden boards under its feet, place the tub in the called for placement. The wooden boards are helpful in evenly spreading out the weight of the tub over the area of the boards as opposed to concentrating all the weight onto four small points.
The next objective is to make certain that the bath tub is leveled all round. This can be accomplished by checking the level and also changing the feet on the bathtub till the level reads degree.
To set up taps, fit all-time low of the outermost versatile tap connector to the proper supply pipe by making a compression join; then do the very same for the other tap.
Activate the water system as well as check all joints and also new pipework for leakages as well as tighten them if necessary. Load the bathtub as well as also examine the overflow outlet and the typical outlet for leakages.
Finally, deal with the bathroom paneling as described in the maker's instruction manual. Tiling and also sealing around the bath tub ought to wait till the bathtub has actually been used at the very least once as this will certainly settle it right into its final setting.
Fitting New Touches
If the tails of the brand-new taps are plastic, then you will certainly require a plastic connector to avoid damages to the thread. One end of the adapter fits on the plastic tail of the tap as well as the various other end offers a link to the existent supply pipelines.
If you require to fit a monobloc, then you will certainly require decreasing couplers, which attaches the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next, place the tap in the placing hole in the bath/basin making certain that the washers remain in location in between the tap and also the sink. Safeguard the tap in place with the supplier offered backnut. As soon as the tap is firmly in place, the supply pipelines can be connected to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with normal faucet connectors. The former type must be connected to the faucet ends first, tightening up just by hand. The supply pipelines can later be connected to the other end. Tighten up both ends with a spanner after both ends have been connected.
Tiling Around the Tub
In the location where the bathroom fulfills the tile, it is required to seal the joins with a silicone rubber caulking. This is important as the fitting can move sufficient to split an inflexible seal, triggering the water to permeate the wall between the bath and the tiling, leading to difficulties with moisture and also possible leakages to the ceiling listed below.
You can select from a variety of coloured sealants to assimilate your components and fittings. They are marketed in tubes as well as cartridges, as well as can securing gaps up to a width of 3mm (1/8 inch). If you have a larger space to fill, you can fill it with spins of drenched paper or soft rope. Bear in mind to constantly fill up the tub with water before sealing, to enable the motion experienced when the tub is in use. The sealant can crack relatively early if you do not take into consideration this movement before securing.
Conversely, ceramic coving or quadrant floor tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise easily available on the marketplace. It is suggested to fit the ceramic tiles utilizing water-resistant or waterproof glue as well as grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you appreciate reading about How to Install a Bathtub Yourself? Put a review further down. We will be delighted to see your thoughts about this page. We hope that you come back again later on. Are you aware of somebody else who is excited by the niche? Why not share it. Thank you so much for taking the time to read it.
Get Quote
Report this page